How deep are wells in Daggett, CA?

The average well depth in Daggett, California is 269 feet, based on 144 wells on record. Well depths range from 66 to 580 feet depending on geology and location.

How much does it cost to drill a well in Daggett, CA?

Well drilling costs in Daggett typically range from $12,105-$20,175 based on the 269-foot average depth. Call Southern California Well Service at (760) 440-8520 for a free estimate.

Average Well Depth in Daggett, CA

Well Statistics for Daggett

269ft

Average Depth

144

Wells on Record

66-580ft

Depth Range

438.1

Avg Yield (GPM)

Need a Well Drilled in Daggett?

Expert well drilling, pump installation, and repair service in Riverside County.

📞 (760) 440-8520 Get Free Estimate →

Well Depth Distribution in Daggett

Based on 144 wells drilled in Daggett, California, the average depth is 269 feet. The median depth is 250 feet, which represents the typical well depth in the area.

66ft
Shallowest 269ft
Average 580ft
Deepest

Shallowest well: 66 feet
Deepest well: 580 feet
Average depth: 269 feet
Median depth: 250 feet

Geology and Groundwater in Daggett

Wells in Daggett reach moderate depths, averaging 269 feet. The area features a mix of alluvial deposits and bedrock formations, with depth varying based on specific location and proximity to fracture zones. Riverside County geology in this region typically involves decomposed granite overlaying harder rock, with groundwater found in fractures and weathered zones.

The average static water level (depth to water when the pump is off) in Daggett wells is approximately 131 feet below ground surface.

Drilling Trends & Well Use

Wells Drilled by Decade

1930s

1940s

1950s

1960s

1970s

1980s

1990s

2000s

2010s

2020s

Wells by Use Type

Domestic 44 (31%)

Public 20 (14%)

Monitoring 20 (14%)

Unknown 17 (12%)

Industrial 14 (10%)

Irrigation - Agriculture 13 (9%)

Sparging 8 (6%)

Test Well 5 (4%)

Estimated Drilling Cost in Daggett

Based on the average well depth of 269 feet, drilling a new well in Daggett typically costs between $12,105 and $20,175. This includes drilling, casing, pump installation, and basic connections. Actual costs vary based on geology, access, and permit requirements.

🔍 Try our free Well Depth Lookup Tool to check well records near your specific address.

📍 Nearby Cities — Well Depth Data

📚 Related Resources

Get Expert Advice for Your Daggett Property

Southern California Well Service has drilled hundreds of wells across Riverside County. We know the local geology and can give you an accurate depth and cost estimate.

Call (760) 440-8520

Licensed C-57 Contractor. CSLB License #1086994.| San Diego, Riverside & San Bernardino Counties

We service all major pump brands including Franklin Electric, Grundfos, Goulds (Xylem), and Sta-Rite (Pentair). Our trucks carry common parts and components for same-day repairs.

Frequently Asked Questions

How do I know if my well pump needs repair?

Common signs include: no water or low pressure, pump cycling on and off rapidly (short cycling), unusual noises, dirty or sandy water, and higher-than-normal electric bills. Any of these warrant a professional inspection.

How much does well pump repair cost?

Simple repairs like pressure switch replacement run

50-$300. Motor or pump replacement typically costs ,500-$4,500 depending on well depth and pump type. We diagnose the issue before recommending repairs.

Can I repair my well pump myself?

Surface-level issues like pressure switch adjustment or breaker resets are safe DIY tasks. However, anything involving pulling the pump from the well requires specialized equipment and should be handled by a licensed contractor to avoid damaging the well casing.

Continue learning about well maintenance and troubleshooting