How deep are wells in Fort Irwin, CA?

The average well depth in Fort Irwin, California is 382 feet, based on 89 wells on record. Well depths range from 20 to 1260 feet depending on geology and location.

How much does it cost to drill a well in Fort Irwin, CA?

Well drilling costs in Fort Irwin typically range from $17,190-$28,650 based on the 382-foot average depth. Call Southern California Well Service at (760) 440-8520 for a free estimate.

Average Well Depth in Fort Irwin, CA

Well Statistics for Fort Irwin

382ft

Average Depth

Wells on Record

20-1260ft

Depth Range

481.5

Avg Yield (GPM)

Need a Well Drilled in Fort Irwin?

Expert well drilling, pump installation, and repair service in San Bernardino County.

📞 (760) 440-8520 Get Free Estimate →

Well Depth Distribution in Fort Irwin

Based on 89 wells drilled in Fort Irwin, California, the average depth is 382 feet. The median depth is 330 feet, which represents the typical well depth in the area.

20ft
Shallowest 382ft
Average 1260ft
Deepest

Shallowest well: 20 feet
Deepest well: 1260 feet
Average depth: 382 feet
Median depth: 330 feet

Geology and Groundwater in Fort Irwin

Wells in Fort Irwin reach moderate depths, averaging 382 feet. The area features a mix of alluvial deposits and bedrock formations, with depth varying based on specific location and proximity to fracture zones. San Bernardino County geology in this region typically involves decomposed granite overlaying harder rock, with groundwater found in fractures and weathered zones.

The average static water level (depth to water when the pump is off) in Fort Irwin wells is approximately 181 feet below ground surface.

Drilling Trends & Well Use

Wells Drilled by Decade

1950s

1980s

1990s

2000s

2010s

2020s

Wells by Use Type

Monitoring 55 (62%)

Public 11 (12%)

Test Well 11 (12%)

Other 7 (8%)

Unknown 4 (4%)

Domestic 1 (1%)

Estimated Drilling Cost in Fort Irwin

Based on the average well depth of 382 feet, drilling a new well in Fort Irwin typically costs between $17,190 and $28,650. This includes drilling, casing, pump installation, and basic connections. Actual costs vary based on geology, access, and permit requirements.

🔍 Try our free Well Depth Lookup Tool to check well records near your specific address.

📍 Nearby Cities — Well Depth Data

📚 Related Resources

Get Expert Advice for Your Fort Irwin Property

Southern California Well Service has drilled hundreds of wells across San Bernardino County. We know the local geology and can give you an accurate depth and cost estimate.

Call (760) 440-8520

Licensed C-57 Contractor. CSLB License #1086994.| San Diego, Riverside & San Bernardino Counties

We service all major pump brands including Franklin Electric, Grundfos, Goulds (Xylem), and Sta-Rite (Pentair). Our trucks carry common parts and components for same-day repairs.

Frequently Asked Questions

How do I know if my well pump needs repair?

Common signs include: no water or low pressure, pump cycling on and off rapidly (short cycling), unusual noises, dirty or sandy water, and higher-than-normal electric bills. Any of these warrant a professional inspection.

How much does well pump repair cost?

Simple repairs like pressure switch replacement run

50-$300. Motor or pump replacement typically costs ,500-$4,500 depending on well depth and pump type. We diagnose the issue before recommending repairs.

Can I repair my well pump myself?

Surface-level issues like pressure switch adjustment or breaker resets are safe DIY tasks. However, anything involving pulling the pump from the well requires specialized equipment and should be handled by a licensed contractor to avoid damaging the well casing.

Continue learning about well maintenance and troubleshooting