How deep are wells in Adelanto, CA?

The average well depth in Adelanto, California is 240 feet, based on 302 wells on record. Well depths range from 25 to 1970 feet depending on geology and location.

How much does it cost to drill a well in Adelanto, CA?

Well drilling costs in Adelanto typically range from $10,800-$18,000 based on the 240-foot average depth. Call Southern California Well Service at (760) 440-8520 for a free estimate.

Average Well Depth in Adelanto, CA

Well Statistics for Adelanto

240ft

Average Depth

302

Wells on Record

25-1970ft

Depth Range

190.5

Avg Yield (GPM)

Need a Well Drilled in Adelanto?

Expert well drilling, pump installation, and repair service in San Diego County.

📞 (760) 440-8520 Get Free Estimate →

Well Depth Distribution in Adelanto

Based on 302 wells drilled in Adelanto, California, the average depth is 240 feet. The median depth is 200 feet, which represents the typical well depth in the area.

25ft
Shallowest 240ft
Average 1970ft
Deepest

Shallowest well: 25 feet
Deepest well: 1970 feet
Average depth: 240 feet
Median depth: 200 feet

Geology and Groundwater in Adelanto

Wells in Adelanto reach moderate depths, averaging 240 feet. The area features a mix of alluvial deposits and bedrock formations, with depth varying based on specific location and proximity to fracture zones. San Diego County geology in this region typically involves decomposed granite overlaying harder rock, with groundwater found in fractures and weathered zones.

The average static water level (depth to water when the pump is off) in Adelanto wells is approximately 148 feet below ground surface.

Drilling Trends & Well Use

Wells Drilled by Decade

1950s

1960s

1970s

1980s

1990s

2000s

2010s

2020s

Wells by Use Type

Domestic 126 (42%)

Monitoring 61 (20%)

Unknown 30 (10%)

Public 26 (9%)

Other 21 (7%)

Cathodic Protection 15 (5%)

Test Well 10 (3%)

Irrigation - Agriculture 9 (3%)

Estimated Drilling Cost in Adelanto

Based on the average well depth of 240 feet, drilling a new well in Adelanto typically costs between $10,800 and $18,000. This includes drilling, casing, pump installation, and basic connections. Actual costs vary based on geology, access, and permit requirements.

🔍 Try our free Well Depth Lookup Tool to check well records near your specific address.

📍 Nearby Cities — Well Depth Data

📚 Related Resources

Get Expert Advice for Your Adelanto Property

Southern California Well Service has drilled hundreds of wells across San Diego County. We know the local geology and can give you an accurate depth and cost estimate.

Call (760) 440-8520

Licensed C-57 Contractor. CSLB License #1086994.| San Diego, Riverside & San Bernardino Counties

We service all major pump brands including Franklin Electric, Grundfos, Goulds (Xylem), and Sta-Rite (Pentair). Our trucks carry common parts and components for same-day repairs.

Frequently Asked Questions

How do I know if my well pump needs repair?

Common signs include: no water or low pressure, pump cycling on and off rapidly (short cycling), unusual noises, dirty or sandy water, and higher-than-normal electric bills. Any of these warrant a professional inspection.

How much does well pump repair cost?

Simple repairs like pressure switch replacement run

50-$300. Motor or pump replacement typically costs ,500-$4,500 depending on well depth and pump type. We diagnose the issue before recommending repairs.

Can I repair my well pump myself?

Surface-level issues like pressure switch adjustment or breaker resets are safe DIY tasks. However, anything involving pulling the pump from the well requires specialized equipment and should be handled by a licensed contractor to avoid damaging the well casing.

Continue learning about well maintenance and troubleshooting