How deep are wells in Lenwood, CA?

The average well depth in Lenwood, California is 243 feet, based on 84 wells on record. Well depths range from 45 to 600 feet depending on geology and location.

How much does it cost to drill a well in Lenwood, CA?

Well drilling costs in Lenwood typically range from $10,935-$18,225 based on the 243-foot average depth. Call Southern California Well Service at (760) 440-8520 for a free estimate.

Average Well Depth in Lenwood, CA

Well Statistics for Lenwood

243ft

Average Depth

Wells on Record

45-600ft

Depth Range

872.0

Avg Yield (GPM)

Need a Well Drilled in Lenwood?

Expert well drilling, pump installation, and repair service in San Bernardino County.

📞 (760) 440-8520 Get Free Estimate →

Well Depth Distribution in Lenwood

Based on 84 wells drilled in Lenwood, California, the average depth is 243 feet. The median depth is 231 feet, which represents the typical well depth in the area.

45ft
Shallowest 243ft
Average 600ft
Deepest

Shallowest well: 45 feet
Deepest well: 600 feet
Average depth: 243 feet
Median depth: 231 feet

Geology and Groundwater in Lenwood

Wells in Lenwood reach moderate depths, averaging 243 feet. The area features a mix of alluvial deposits and bedrock formations, with depth varying based on specific location and proximity to fracture zones. San Bernardino County geology in this region typically involves decomposed granite overlaying harder rock, with groundwater found in fractures and weathered zones.

The average static water level (depth to water when the pump is off) in Lenwood wells is approximately 119 feet below ground surface.

Drilling Trends & Well Use

Wells Drilled by Decade

1950s

1960s

1970s

1980s

1990s

2000s

Wells by Use Type

Domestic 44 (52%)

Public 17 (20%)

Irrigation - Agriculture 8 (10%)

Monitoring 6 (7%)

Industrial 4 (5%)

Test Well 2 (2%)

Cathodic Protection 2 (2%)

Unknown 1 (1%)

Estimated Drilling Cost in Lenwood

Based on the average well depth of 243 feet, drilling a new well in Lenwood typically costs between $10,935 and $18,225. This includes drilling, casing, pump installation, and basic connections. Actual costs vary based on geology, access, and permit requirements.

🔍 Try our free Well Depth Lookup Tool to check well records near your specific address.

📍 Nearby Cities — Well Depth Data

📚 Related Resources

Get Expert Advice for Your Lenwood Property

Southern California Well Service has drilled hundreds of wells across San Bernardino County. We know the local geology and can give you an accurate depth and cost estimate.

Call (760) 440-8520

Licensed C-57 Contractor. CSLB License #1086994.| San Diego, Riverside & San Bernardino Counties

We service all major pump brands including Franklin Electric, Grundfos, Goulds (Xylem), and Sta-Rite (Pentair). Our trucks carry common parts and components for same-day repairs.

Frequently Asked Questions

How do I know if my well pump needs repair?

Common signs include: no water or low pressure, pump cycling on and off rapidly (short cycling), unusual noises, dirty or sandy water, and higher-than-normal electric bills. Any of these warrant a professional inspection.

How much does well pump repair cost?

Simple repairs like pressure switch replacement run

50-$300. Motor or pump replacement typically costs ,500-$4,500 depending on well depth and pump type. We diagnose the issue before recommending repairs.

Can I repair my well pump myself?

Surface-level issues like pressure switch adjustment or breaker resets are safe DIY tasks. However, anything involving pulling the pump from the well requires specialized equipment and should be handled by a licensed contractor to avoid damaging the well casing.

Continue learning about well maintenance and troubleshooting