How deep are wells in Upland, CA?

The average well depth in Upland, California is 277 feet, based on 49 wells on record. Well depths range from 5 to 1040 feet depending on geology and location.

How much does it cost to drill a well in Upland, CA?

Well drilling costs in Upland typically range from $12,465-$20,775 based on the 277-foot average depth. Call Southern California Well Service at (760) 440-8520 for a free estimate.

Average Well Depth in Upland, CA

Well Statistics for Upland

277ft

Average Depth

Wells on Record

5-1040ft

Depth Range

973.0

Avg Yield (GPM)

Need a Well Drilled in Upland?

Expert well drilling, pump installation, and repair service in San Bernardino County.

📞 (760) 440-8520 Get Free Estimate →

Well Depth Distribution in Upland

Based on 49 wells drilled in Upland, California, the average depth is 277 feet. The median depth is 82 feet, which represents the typical well depth in the area.

5ft
Shallowest 277ft
Average 1040ft
Deepest

Shallowest well: 5 feet
Deepest well: 1040 feet
Average depth: 277 feet
Median depth: 82 feet

Geology and Groundwater in Upland

Wells in Upland reach moderate depths, averaging 277 feet. The area features a mix of alluvial deposits and bedrock formations, with depth varying based on specific location and proximity to fracture zones. San Bernardino County geology in this region typically involves decomposed granite overlaying harder rock, with groundwater found in fractures and weathered zones.

The average static water level (depth to water when the pump is off) in Upland wells is approximately 549 feet below ground surface.

Drilling Trends & Well Use

Wells Drilled by Decade

1920s

1930s

1980s

1990s

2000s

2010s

Wells by Use Type

Vapor Extraction 13 (27%)

Other 12 (24%)

Test Well 8 (16%)

Unknown 5 (10%)

Domestic 4 (8%)

Public 4 (8%)

Monitoring 2 (4%)

Cathodic Protection 1 (2%)

Estimated Drilling Cost in Upland

Based on the average well depth of 277 feet, drilling a new well in Upland typically costs between $12,465 and $20,775. This includes drilling, casing, pump installation, and basic connections. Actual costs vary based on geology, access, and permit requirements.

🔍 Try our free Well Depth Lookup Tool to check well records near your specific address.

📍 Nearby Cities — Well Depth Data

📚 Related Resources

Get Expert Advice for Your Upland Property

Southern California Well Service has drilled hundreds of wells across San Bernardino County. We know the local geology and can give you an accurate depth and cost estimate.

Call (760) 440-8520

Licensed C-57 Contractor. CSLB License #1086994.| San Diego, Riverside & San Bernardino Counties

We service all major pump brands including Franklin Electric, Grundfos, Goulds (Xylem), and Sta-Rite (Pentair). Our trucks carry common parts and components for same-day repairs.

Frequently Asked Questions

How do I know if my well pump needs repair?

Common signs include: no water or low pressure, pump cycling on and off rapidly (short cycling), unusual noises, dirty or sandy water, and higher-than-normal electric bills. Any of these warrant a professional inspection.

How much does well pump repair cost?

Simple repairs like pressure switch replacement run

50-$300. Motor or pump replacement typically costs ,500-$4,500 depending on well depth and pump type. We diagnose the issue before recommending repairs.

Can I repair my well pump myself?

Surface-level issues like pressure switch adjustment or breaker resets are safe DIY tasks. However, anything involving pulling the pump from the well requires specialized equipment and should be handled by a licensed contractor to avoid damaging the well casing.

Continue learning about well maintenance and troubleshooting