How deep are wells in Wrightwood, CA?

The average well depth in Wrightwood, California is 262 feet, based on 44 wells on record. Well depths range from 40 to 1081 feet depending on geology and location.

How much does it cost to drill a well in Wrightwood, CA?

Well drilling costs in Wrightwood typically range from $11,790-$19,650 based on the 262-foot average depth. Call Southern California Well Service at (760) 440-8520 for a free estimate.

Average Well Depth in Wrightwood, CA

Well Statistics for Wrightwood

262ft

Average Depth

Wells on Record

40-1081ft

Depth Range

210.2

Avg Yield (GPM)

Need a Well Drilled in Wrightwood?

Expert well drilling, pump installation, and repair service in San Bernardino County.

📞 (760) 440-8520 Get Free Estimate →

Well Depth Distribution in Wrightwood

Based on 44 wells drilled in Wrightwood, California, the average depth is 262 feet. The median depth is 275 feet, which represents the typical well depth in the area.

40ft
Shallowest 262ft
Average 1081ft
Deepest

Shallowest well: 40 feet
Deepest well: 1081 feet
Average depth: 262 feet
Median depth: 275 feet

Geology and Groundwater in Wrightwood

Wells in Wrightwood reach moderate depths, averaging 262 feet. The area features a mix of alluvial deposits and bedrock formations, with depth varying based on specific location and proximity to fracture zones. San Bernardino County geology in this region typically involves decomposed granite overlaying harder rock, with groundwater found in fractures and weathered zones.

The average static water level (depth to water when the pump is off) in Wrightwood wells is approximately 96 feet below ground surface.

Drilling Trends & Well Use

Wells Drilled by Decade

1970s

1980s

1990s

2000s

2010s

2020s

Wells by Use Type

Domestic 17 (39%)

Monitoring 8 (18%)

Test Well 6 (14%)

Public 5 (11%)

Vapor Extraction 4 (9%)

Unknown 2 (5%)

Other 1 (2%)

Cathodic Protection 1 (2%)

Estimated Drilling Cost in Wrightwood

Based on the average well depth of 262 feet, drilling a new well in Wrightwood typically costs between $11,790 and $19,650. This includes drilling, casing, pump installation, and basic connections. Actual costs vary based on geology, access, and permit requirements.

🔍 Try our free Well Depth Lookup Tool to check well records near your specific address.

📍 Nearby Cities — Well Depth Data

📚 Related Resources

Get Expert Advice for Your Wrightwood Property

Southern California Well Service has drilled hundreds of wells across San Bernardino County. We know the local geology and can give you an accurate depth and cost estimate.

Call (760) 440-8520

Licensed C-57 Contractor. CSLB License #1086994.| San Diego, Riverside & San Bernardino Counties

We service all major pump brands including Franklin Electric, Grundfos, Goulds (Xylem), and Sta-Rite (Pentair). Our trucks carry common parts and components for same-day repairs.

Frequently Asked Questions

How do I know if my well pump needs repair?

Common signs include: no water or low pressure, pump cycling on and off rapidly (short cycling), unusual noises, dirty or sandy water, and higher-than-normal electric bills. Any of these warrant a professional inspection.

How much does well pump repair cost?

Simple repairs like pressure switch replacement run

50-$300. Motor or pump replacement typically costs ,500-$4,500 depending on well depth and pump type. We diagnose the issue before recommending repairs.

Can I repair my well pump myself?

Surface-level issues like pressure switch adjustment or breaker resets are safe DIY tasks. However, anything involving pulling the pump from the well requires specialized equipment and should be handled by a licensed contractor to avoid damaging the well casing.

Continue learning about well maintenance and troubleshooting