How deep are wells in Yermo, CA?

The average well depth in Yermo, California is 245 feet, based on 451 wells on record. Well depths range from 3 to 800 feet depending on geology and location.

How much does it cost to drill a well in Yermo, CA?

Well drilling costs in Yermo typically range from $11,025-$18,375 based on the 245-foot average depth. Call Southern California Well Service at (760) 440-8520 for a free estimate.

Average Well Depth in Yermo, CA

Well Statistics for Yermo

245ft

Average Depth

451

Wells on Record

3-800ft

Depth Range

216.6

Avg Yield (GPM)

Need a Well Drilled in Yermo?

Expert well drilling, pump installation, and repair service in San Bernardino County.

📞 (760) 440-8520 Get Free Estimate →

Well Depth Distribution in Yermo

Based on 451 wells drilled in Yermo, California, the average depth is 245 feet. The median depth is 240 feet, which represents the typical well depth in the area.

3ft
Shallowest 245ft
Average 800ft
Deepest

Shallowest well: 3 feet
Deepest well: 800 feet
Average depth: 245 feet
Median depth: 240 feet

Geology and Groundwater in Yermo

Wells in Yermo reach moderate depths, averaging 245 feet. The area features a mix of alluvial deposits and bedrock formations, with depth varying based on specific location and proximity to fracture zones. San Bernardino County geology in this region typically involves decomposed granite overlaying harder rock, with groundwater found in fractures and weathered zones.

The average static water level (depth to water when the pump is off) in Yermo wells is approximately 143 feet below ground surface.

Drilling Trends & Well Use

Wells Drilled by Decade

1900s

1920s

1930s

1950s

1960s

1970s

1980s

201

1990s

2000s

2010s

2020s

Wells by Use Type

Domestic 256 (58%)

Cathodic Protection 64 (14%)

Public 31 (7%)

Monitoring 28 (6%)

Irrigation - Agriculture 25 (6%)

Unknown 18 (4%)

Industrial 13 (3%)

Destruction 7 (2%)

Estimated Drilling Cost in Yermo

Based on the average well depth of 245 feet, drilling a new well in Yermo typically costs between $11,025 and $18,375. This includes drilling, casing, pump installation, and basic connections. Actual costs vary based on geology, access, and permit requirements.

🔍 Try our free Well Depth Lookup Tool to check well records near your specific address.

📍 Nearby Cities — Well Depth Data

📚 Related Resources

Get Expert Advice for Your Yermo Property

Southern California Well Service has drilled hundreds of wells across San Bernardino County. We know the local geology and can give you an accurate depth and cost estimate.

Call (760) 440-8520

Licensed C-57 Contractor. CSLB License #1086994.| San Diego, Riverside & San Bernardino Counties

We service all major pump brands including Franklin Electric, Grundfos, Goulds (Xylem), and Sta-Rite (Pentair). Our trucks carry common parts and components for same-day repairs.

Frequently Asked Questions

How do I know if my well pump needs repair?

Common signs include: no water or low pressure, pump cycling on and off rapidly (short cycling), unusual noises, dirty or sandy water, and higher-than-normal electric bills. Any of these warrant a professional inspection.

How much does well pump repair cost?

Simple repairs like pressure switch replacement run

50-$300. Motor or pump replacement typically costs ,500-$4,500 depending on well depth and pump type. We diagnose the issue before recommending repairs.

Can I repair my well pump myself?

Surface-level issues like pressure switch adjustment or breaker resets are safe DIY tasks. However, anything involving pulling the pump from the well requires specialized equipment and should be handled by a licensed contractor to avoid damaging the well casing.

Continue learning about well maintenance and troubleshooting