How deep are wells in Anza, CA?

The average well depth in Anza, California is 348 feet, based on 1584 wells on record. Well depths range from 1 to 1370 feet depending on geology and location.

How much does it cost to drill a well in Anza, CA?

Well drilling costs in Anza typically range from $15,660-$26,100 based on the 348-foot average depth. Call Southern California Well Service at (760) 440-8520 for a free estimate.

Average Well Depth in Anza, CA

Well Statistics for Anza

348ft

Average Depth

1,584

Wells on Record

1-1370ft

Depth Range

40.3

Avg Yield (GPM)

Need a Well Drilled in Anza?

Expert well drilling, pump installation, and repair service in Riverside County.

📞 (760) 440-8520 Get Free Estimate →

Well Depth Distribution in Anza

Based on 1,584 wells drilled in Anza, California, the average depth is 348 feet. The median depth is 310 feet, which represents the typical well depth in the area.

1ft
Shallowest 348ft
Average 1370ft
Deepest

Shallowest well: 1 feet
Deepest well: 1370 feet
Average depth: 348 feet
Median depth: 310 feet

Geology and Groundwater in Anza

Wells in Anza reach moderate depths, averaging 348 feet. The area features a mix of alluvial deposits and bedrock formations, with depth varying based on specific location and proximity to fracture zones. Riverside County geology in this region typically involves decomposed granite overlaying harder rock, with groundwater found in fractures and weathered zones.

The average static water level (depth to water when the pump is off) in Anza wells is approximately 133 feet below ground surface.

Drilling Trends & Well Use

Wells Drilled by Decade

1920s

1930s

1940s

1950s

1960s

1970s

268

1980s

250

1990s

164

2000s

374

2010s

272

2020s

129

Wells by Use Type

Domestic 1417 (90%)

Irrigation - Agriculture 74 (5%)

Unknown 34 (2%)

Irrigation - Landscape 21 (1%)

Public 15 (1%)

Monitoring 15 (1%)

Test Well 4 (0%)

Industrial 2 (0%)

Estimated Drilling Cost in Anza

Based on the average well depth of 348 feet, drilling a new well in Anza typically costs between $15,660 and $26,100. This includes drilling, casing, pump installation, and basic connections. Actual costs vary based on geology, access, and permit requirements.

🔍 Try our free Well Depth Lookup Tool to check well records near your specific address.

📍 Nearby Cities — Well Depth Data

📚 Related Resources

Get Expert Advice for Your Anza Property

Southern California Well Service has drilled hundreds of wells across Riverside County. We know the local geology and can give you an accurate depth and cost estimate.

Call (760) 440-8520

Licensed C-57 Contractor. CSLB License #1086994.| San Diego, Riverside & San Bernardino Counties

We service all major pump brands including Franklin Electric, Grundfos, Goulds (Xylem), and Sta-Rite (Pentair). Our trucks carry common parts and components for same-day repairs.

Frequently Asked Questions

How do I know if my well pump needs repair?

Common signs include: no water or low pressure, pump cycling on and off rapidly (short cycling), unusual noises, dirty or sandy water, and higher-than-normal electric bills. Any of these warrant a professional inspection.

How much does well pump repair cost?

Simple repairs like pressure switch replacement run

50-$300. Motor or pump replacement typically costs ,500-$4,500 depending on well depth and pump type. We diagnose the issue before recommending repairs.

Can I repair my well pump myself?

Surface-level issues like pressure switch adjustment or breaker resets are safe DIY tasks. However, anything involving pulling the pump from the well requires specialized equipment and should be handled by a licensed contractor to avoid damaging the well casing.

Continue learning about well maintenance and troubleshooting