How deep are wells in Corona, CA?

The average well depth in Corona, California is 194 feet, based on 631 wells on record. Well depths range from 6 to 1090 feet depending on geology and location.

How much does it cost to drill a well in Corona, CA?

Well drilling costs in Corona typically range from $8,730-$14,550 based on the 194-foot average depth. Call Southern California Well Service at (760) 440-8520 for a free estimate.

Average Well Depth in Corona, CA

Well Statistics for Corona

194ft

Average Depth

631

Wells on Record

6-1090ft

Depth Range

309.0

Avg Yield (GPM)

Need a Well Drilled in Corona?

Expert well drilling, pump installation, and repair service in Riverside County.

📞 (760) 440-8520 Get Free Estimate →

Well Depth Distribution in Corona

Based on 631 wells drilled in Corona, California, the average depth is 194 feet. The median depth is 140 feet, which represents the typical well depth in the area.

6ft
Shallowest 194ft
Average 1090ft
Deepest

Shallowest well: 6 feet
Deepest well: 1090 feet
Average depth: 194 feet
Median depth: 140 feet

Geology and Groundwater in Corona

Corona benefits from relatively shallow groundwater, with wells averaging just 194 feet deep. The area's alluvial deposits and sedimentary formations allow easier access to productive aquifers. Shallower wells in this region typically use rotary drilling methods and can often be completed more quickly and at lower cost than deeper bedrock wells.

The average static water level (depth to water when the pump is off) in Corona wells is approximately 74 feet below ground surface.

Drilling Trends & Well Use

Wells Drilled by Decade

1920s

1930s

1950s

1960s

1970s

1980s

1990s

100

2000s

163

2010s

2020s

Wells by Use Type

Monitoring 226 (37%)

Domestic 189 (31%)

Irrigation - Agriculture 56 (9%)

Other 40 (7%)

Unknown 40 (7%)

Public 31 (5%)

Industrial 16 (3%)

Cathodic Protection 13 (2%)

Estimated Drilling Cost in Corona

Based on the average well depth of 194 feet, drilling a new well in Corona typically costs between $8,730 and $14,550. This includes drilling, casing, pump installation, and basic connections. Actual costs vary based on geology, access, and permit requirements.

🔍 Try our free Well Depth Lookup Tool to check well records near your specific address.

📍 Nearby Cities — Well Depth Data

📚 Related Resources

Get Expert Advice for Your Corona Property

Southern California Well Service has drilled hundreds of wells across Riverside County. We know the local geology and can give you an accurate depth and cost estimate.

Call (760) 440-8520

Licensed C-57 Contractor. CSLB License #1086994.| San Diego, Riverside & San Bernardino Counties

We service all major pump brands including Franklin Electric, Grundfos, Goulds (Xylem), and Sta-Rite (Pentair). Our trucks carry common parts and components for same-day repairs.

Frequently Asked Questions

How do I know if my well pump needs repair?

Common signs include: no water or low pressure, pump cycling on and off rapidly (short cycling), unusual noises, dirty or sandy water, and higher-than-normal electric bills. Any of these warrant a professional inspection.

How much does well pump repair cost?

Simple repairs like pressure switch replacement run

50-$300. Motor or pump replacement typically costs ,500-$4,500 depending on well depth and pump type. We diagnose the issue before recommending repairs.

Can I repair my well pump myself?

Surface-level issues like pressure switch adjustment or breaker resets are safe DIY tasks. However, anything involving pulling the pump from the well requires specialized equipment and should be handled by a licensed contractor to avoid damaging the well casing.

Continue learning about well maintenance and troubleshooting