How deep are wells in Perris, CA?

The average well depth in Perris, California is 311 feet, based on 1152 wells on record. Well depths range from 10 to 1400 feet depending on geology and location.

How much does it cost to drill a well in Perris, CA?

Well drilling costs in Perris typically range from $13,995-$23,325 based on the 311-foot average depth. Call Southern California Well Service at (760) 440-8520 for a free estimate.

Average Well Depth in Perris, CA

Well Statistics for Perris

311ft

Average Depth

1,152

Wells on Record

10-1400ft

Depth Range

57.5

Avg Yield (GPM)

Need a Well Drilled in Perris?

Expert well drilling, pump installation, and repair service in Riverside County.

📞 (760) 440-8520 Get Free Estimate →

Well Depth Distribution in Perris

Based on 1,152 wells drilled in Perris, California, the average depth is 311 feet. The median depth is 211 feet, which represents the typical well depth in the area.

10ft
Shallowest 311ft
Average 1400ft
Deepest

Shallowest well: 10 feet
Deepest well: 1400 feet
Average depth: 311 feet
Median depth: 211 feet

Geology and Groundwater in Perris

Wells in Perris reach moderate depths, averaging 311 feet. The area features a mix of alluvial deposits and bedrock formations, with depth varying based on specific location and proximity to fracture zones. Riverside County geology in this region typically involves decomposed granite overlaying harder rock, with groundwater found in fractures and weathered zones.

The average static water level (depth to water when the pump is off) in Perris wells is approximately 73 feet below ground surface.

Drilling Trends & Well Use

Wells Drilled by Decade

1920s

1940s

1950s

1960s

1970s

1980s

104

1990s

196

2000s

343

2010s

244

2020s

Wells by Use Type

Domestic 690 (60%)

Irrigation - Agriculture 187 (16%)

Monitoring 136 (12%)

Other 62 (5%)

Unknown 28 (2%)

Public 23 (2%)

Irrigation - Landscape 10 (1%)

Sparging 7 (1%)

Estimated Drilling Cost in Perris

Based on the average well depth of 311 feet, drilling a new well in Perris typically costs between $13,995 and $23,325. This includes drilling, casing, pump installation, and basic connections. Actual costs vary based on geology, access, and permit requirements.

🔍 Try our free Well Depth Lookup Tool to check well records near your specific address.

📍 Nearby Cities — Well Depth Data

📚 Related Resources

Get Expert Advice for Your Perris Property

Southern California Well Service has drilled hundreds of wells across Riverside County. We know the local geology and can give you an accurate depth and cost estimate.

Call (760) 440-8520

Licensed C-57 Contractor. CSLB License #1086994.| San Diego, Riverside & San Bernardino Counties

We service all major pump brands including Franklin Electric, Grundfos, Goulds (Xylem), and Sta-Rite (Pentair). Our trucks carry common parts and components for same-day repairs.

Frequently Asked Questions

How do I know if my well pump needs repair?

Common signs include: no water or low pressure, pump cycling on and off rapidly (short cycling), unusual noises, dirty or sandy water, and higher-than-normal electric bills. Any of these warrant a professional inspection.

How much does well pump repair cost?

Simple repairs like pressure switch replacement run

50-$300. Motor or pump replacement typically costs ,500-$4,500 depending on well depth and pump type. We diagnose the issue before recommending repairs.

Can I repair my well pump myself?

Surface-level issues like pressure switch adjustment or breaker resets are safe DIY tasks. However, anything involving pulling the pump from the well requires specialized equipment and should be handled by a licensed contractor to avoid damaging the well casing.

Continue learning about well maintenance and troubleshooting