How deep are wells in Bloomington, CA?

The average well depth in Bloomington, California is 212 feet, based on 95 wells on record. Well depths range from 80 to 750 feet depending on geology and location.

How much does it cost to drill a well in Bloomington, CA?

Well drilling costs in Bloomington typically range from $9,540-$15,900 based on the 212-foot average depth. Call Southern California Well Service at (760) 440-8520 for a free estimate.

Average Well Depth in Bloomington, CA

Well Statistics for Bloomington

212ft

Average Depth

Wells on Record

80-750ft

Depth Range

733.0

Avg Yield (GPM)

Need a Well Drilled in Bloomington?

Expert well drilling, pump installation, and repair service in Riverside County.

📞 (760) 440-8520 Get Free Estimate →

Well Depth Distribution in Bloomington

Based on 95 wells drilled in Bloomington, California, the average depth is 212 feet. The median depth is 154 feet, which represents the typical well depth in the area.

80ft
Shallowest 212ft
Average 750ft
Deepest

Shallowest well: 80 feet
Deepest well: 750 feet
Average depth: 212 feet
Median depth: 154 feet

Geology and Groundwater in Bloomington

Wells in Bloomington reach moderate depths, averaging 212 feet. The area features a mix of alluvial deposits and bedrock formations, with depth varying based on specific location and proximity to fracture zones. Riverside County geology in this region typically involves decomposed granite overlaying harder rock, with groundwater found in fractures and weathered zones.

The average static water level (depth to water when the pump is off) in Bloomington wells is approximately 164 feet below ground surface.

Drilling Trends & Well Use

Wells Drilled by Decade

1950s

1960s

1980s

1990s

2000s

2010s

2020s

Wells by Use Type

Monitoring 62 (67%)

Domestic 7 (8%)

Irrigation - Agriculture 5 (5%)

Cathodic Protection 5 (5%)

Test Well 4 (4%)

Vapor Extraction 4 (4%)

Unknown 3 (3%)

Other 2 (2%)

Estimated Drilling Cost in Bloomington

Based on the average well depth of 212 feet, drilling a new well in Bloomington typically costs between $9,540 and $15,900. This includes drilling, casing, pump installation, and basic connections. Actual costs vary based on geology, access, and permit requirements.

🔍 Try our free Well Depth Lookup Tool to check well records near your specific address.

📍 Nearby Cities — Well Depth Data

📚 Related Resources

Get Expert Advice for Your Bloomington Property

Southern California Well Service has drilled hundreds of wells across Riverside County. We know the local geology and can give you an accurate depth and cost estimate.

Call (760) 440-8520

Licensed C-57 Contractor. CSLB License #1086994.| San Diego, Riverside & San Bernardino Counties

We service all major pump brands including Franklin Electric, Grundfos, Goulds (Xylem), and Sta-Rite (Pentair). Our trucks carry common parts and components for same-day repairs.

Frequently Asked Questions

How do I know if my well pump needs repair?

Common signs include: no water or low pressure, pump cycling on and off rapidly (short cycling), unusual noises, dirty or sandy water, and higher-than-normal electric bills. Any of these warrant a professional inspection.

How much does well pump repair cost?

Simple repairs like pressure switch replacement run

50-$300. Motor or pump replacement typically costs ,500-$4,500 depending on well depth and pump type. We diagnose the issue before recommending repairs.

Can I repair my well pump myself?

Surface-level issues like pressure switch adjustment or breaker resets are safe DIY tasks. However, anything involving pulling the pump from the well requires specialized equipment and should be handled by a licensed contractor to avoid damaging the well casing.

Continue learning about well maintenance and troubleshooting