How deep are wells in Colton, CA?

The average well depth in Colton, California is 226 feet, based on 498 wells on record. Well depths range from 7 to 1300 feet depending on geology and location.

How much does it cost to drill a well in Colton, CA?

Well drilling costs in Colton typically range from $10,170-$16,950 based on the 226-foot average depth. Call Southern California Well Service at (760) 440-8520 for a free estimate.

Average Well Depth in Colton, CA

Well Statistics for Colton

226ft

Average Depth

498

Wells on Record

7-1300ft

Depth Range

496.2

Avg Yield (GPM)

Need a Well Drilled in Colton?

Expert well drilling, pump installation, and repair service in Riverside County.

📞 (760) 440-8520 Get Free Estimate →

Well Depth Distribution in Colton

Based on 498 wells drilled in Colton, California, the average depth is 226 feet. The median depth is 153 feet, which represents the typical well depth in the area.

7ft
Shallowest 226ft
Average 1300ft
Deepest

Shallowest well: 7 feet
Deepest well: 1300 feet
Average depth: 226 feet
Median depth: 153 feet

Geology and Groundwater in Colton

Wells in Colton reach moderate depths, averaging 226 feet. The area features a mix of alluvial deposits and bedrock formations, with depth varying based on specific location and proximity to fracture zones. Riverside County geology in this region typically involves decomposed granite overlaying harder rock, with groundwater found in fractures and weathered zones.

The average static water level (depth to water when the pump is off) in Colton wells is approximately 114 feet below ground surface.

Drilling Trends & Well Use

Wells Drilled by Decade

1910s

1920s

1930s

1940s

1950s

1960s

1970s

1980s

1990s

104

2000s

138

2010s

107

2020s

Wells by Use Type

Domestic 177 (36%)

Monitoring 137 (28%)

Unknown 68 (14%)

Other 46 (9%)

Irrigation - Agriculture 18 (4%)

Test Well 16 (3%)

Public 13 (3%)

Industrial 10 (2%)

Estimated Drilling Cost in Colton

Based on the average well depth of 226 feet, drilling a new well in Colton typically costs between $10,170 and $16,950. This includes drilling, casing, pump installation, and basic connections. Actual costs vary based on geology, access, and permit requirements.

🔍 Try our free Well Depth Lookup Tool to check well records near your specific address.

📍 Nearby Cities — Well Depth Data

📚 Related Resources

Get Expert Advice for Your Colton Property

Southern California Well Service has drilled hundreds of wells across Riverside County. We know the local geology and can give you an accurate depth and cost estimate.

Call (760) 440-8520

Licensed C-57 Contractor. CSLB License #1086994.| San Diego, Riverside & San Bernardino Counties

We service all major pump brands including Franklin Electric, Grundfos, Goulds (Xylem), and Sta-Rite (Pentair). Our trucks carry common parts and components for same-day repairs.

Frequently Asked Questions

How do I know if my well pump needs repair?

Common signs include: no water or low pressure, pump cycling on and off rapidly (short cycling), unusual noises, dirty or sandy water, and higher-than-normal electric bills. Any of these warrant a professional inspection.

How much does well pump repair cost?

Simple repairs like pressure switch replacement run

50-$300. Motor or pump replacement typically costs ,500-$4,500 depending on well depth and pump type. We diagnose the issue before recommending repairs.

Can I repair my well pump myself?

Surface-level issues like pressure switch adjustment or breaker resets are safe DIY tasks. However, anything involving pulling the pump from the well requires specialized equipment and should be handled by a licensed contractor to avoid damaging the well casing.

Continue learning about well maintenance and troubleshooting