How deep are wells in Norco, CA?

The average well depth in Norco, California is 87 feet, based on 264 wells on record. Well depths range from 10 to 917 feet depending on geology and location.

How much does it cost to drill a well in Norco, CA?

Well drilling costs in Norco typically range from $3,915-$6,525 based on the 87-foot average depth. Call Southern California Well Service at (760) 440-8520 for a free estimate.

Average Well Depth in Norco, CA

Well Statistics for Norco

87ft

Average Depth

264

Wells on Record

10-917ft

Depth Range

642.5

Avg Yield (GPM)

Need a Well Drilled in Norco?

Expert well drilling, pump installation, and repair service in Riverside County.

📞 (760) 440-8520 Get Free Estimate →

Well Depth Distribution in Norco

Based on 264 wells drilled in Norco, California, the average depth is 87 feet. The median depth is 50 feet, which represents the typical well depth in the area.

10ft
Shallowest 87ft
Average 917ft
Deepest

Shallowest well: 10 feet
Deepest well: 917 feet
Average depth: 87 feet
Median depth: 50 feet

Geology and Groundwater in Norco

Norco benefits from relatively shallow groundwater, with wells averaging just 87 feet deep. The area's alluvial deposits and sedimentary formations allow easier access to productive aquifers. Shallower wells in this region typically use rotary drilling methods and can often be completed more quickly and at lower cost than deeper bedrock wells.

The average static water level (depth to water when the pump is off) in Norco wells is approximately 36 feet below ground surface.

Drilling Trends & Well Use

Wells Drilled by Decade

1920s

1930s

1940s

1950s

1960s

1970s

1980s

1990s

2000s

114

2010s

2020s

Wells by Use Type

Monitoring 142 (54%)

Unknown 43 (16%)

Domestic 38 (15%)

Irrigation - Agriculture 21 (8%)

Injection 10 (4%)

Public 4 (2%)

Industrial 2 (1%)

Test Well 2 (1%)

Estimated Drilling Cost in Norco

Based on the average well depth of 87 feet, drilling a new well in Norco typically costs between $3,915 and $6,525. This includes drilling, casing, pump installation, and basic connections. Actual costs vary based on geology, access, and permit requirements.

🔍 Try our free Well Depth Lookup Tool to check well records near your specific address.

📍 Nearby Cities — Well Depth Data

📚 Related Resources

Get Expert Advice for Your Norco Property

Southern California Well Service has drilled hundreds of wells across Riverside County. We know the local geology and can give you an accurate depth and cost estimate.

Call (760) 440-8520

Licensed C-57 Contractor. CSLB License #1086994.| San Diego, Riverside & San Bernardino Counties

We service all major pump brands including Franklin Electric, Grundfos, Goulds (Xylem), and Sta-Rite (Pentair). Our trucks carry common parts and components for same-day repairs.

Frequently Asked Questions

How do I know if my well pump needs repair?

Common signs include: no water or low pressure, pump cycling on and off rapidly (short cycling), unusual noises, dirty or sandy water, and higher-than-normal electric bills. Any of these warrant a professional inspection.

How much does well pump repair cost?

Simple repairs like pressure switch replacement run

50-$300. Motor or pump replacement typically costs ,500-$4,500 depending on well depth and pump type. We diagnose the issue before recommending repairs.

Can I repair my well pump myself?

Surface-level issues like pressure switch adjustment or breaker resets are safe DIY tasks. However, anything involving pulling the pump from the well requires specialized equipment and should be handled by a licensed contractor to avoid damaging the well casing.

Continue learning about well maintenance and troubleshooting