How deep are wells in Palm Desert, CA?

The average well depth in Palm Desert, California is 724 feet, based on 128 wells on record. Well depths range from 25 to 1420 feet depending on geology and location.

How much does it cost to drill a well in Palm Desert, CA?

Well drilling costs in Palm Desert typically range from $32,580-$54,300 based on the 724-foot average depth. Call Southern California Well Service at (760) 440-8520 for a free estimate.

Average Well Depth in Palm Desert, CA

Well Statistics for Palm Desert

724ft

Average Depth

128

Wells on Record

25-1420ft

Depth Range

1988.6

Avg Yield (GPM)

Need a Well Drilled in Palm Desert?

Expert well drilling, pump installation, and repair service in Riverside County.

📞 (760) 440-8520 Get Free Estimate →

Well Depth Distribution in Palm Desert

Based on 128 wells drilled in Palm Desert, California, the average depth is 724 feet. The median depth is 718 feet, which represents the typical well depth in the area.

25ft
Shallowest 724ft
Average 1420ft
Deepest

Shallowest well: 25 feet
Deepest well: 1420 feet
Average depth: 724 feet
Median depth: 718 feet

Geology and Groundwater in Palm Desert

Palm Desert sits in an area with deep bedrock, typically requiring wells to penetrate granite or metamorphic formations. The average depth of 724 feet reflects the need to drill through hard rock layers to reach productive aquifers. These deeper wells often require air rotary or DTH (down-the-hole) hammer drilling methods. Well depths vary significantly—from 25 to 1420 feet—reflecting diverse geological conditions across the area.

The average static water level (depth to water when the pump is off) in Palm Desert wells is approximately 219 feet below ground surface.

Drilling Trends & Well Use

Wells Drilled by Decade

1940s

1950s

1960s

1970s

1980s

1990s

2000s

2010s

2020s

Wells by Use Type

Public 41 (33%)

Irrigation - Agriculture 35 (28%)

Monitoring 16 (13%)

Domestic 12 (10%)

Cathodic Protection 10 (8%)

Irrigation - Landscape 4 (3%)

Vapor Extraction 3 (2%)

Unknown 2 (2%)

Estimated Drilling Cost in Palm Desert

Based on the average well depth of 724 feet, drilling a new well in Palm Desert typically costs between $32,580 and $54,300. This includes drilling, casing, pump installation, and basic connections. Actual costs vary based on geology, access, and permit requirements.

🔍 Try our free Well Depth Lookup Tool to check well records near your specific address.

📍 Nearby Cities — Well Depth Data

📚 Related Resources

Get Expert Advice for Your Palm Desert Property

Southern California Well Service has drilled hundreds of wells across Riverside County. We know the local geology and can give you an accurate depth and cost estimate.

Call (760) 440-8520

Licensed C-57 Contractor. CSLB License #1086994.| San Diego, Riverside & San Bernardino Counties

We service all major pump brands including Franklin Electric, Grundfos, Goulds (Xylem), and Sta-Rite (Pentair). Our trucks carry common parts and components for same-day repairs.

Frequently Asked Questions

How do I know if my well pump needs repair?

Common signs include: no water or low pressure, pump cycling on and off rapidly (short cycling), unusual noises, dirty or sandy water, and higher-than-normal electric bills. Any of these warrant a professional inspection.

How much does well pump repair cost?

Simple repairs like pressure switch replacement run

50-$300. Motor or pump replacement typically costs ,500-$4,500 depending on well depth and pump type. We diagnose the issue before recommending repairs.

Can I repair my well pump myself?

Surface-level issues like pressure switch adjustment or breaker resets are safe DIY tasks. However, anything involving pulling the pump from the well requires specialized equipment and should be handled by a licensed contractor to avoid damaging the well casing.

Continue learning about well maintenance and troubleshooting