How deep are wells in Redlands, CA?

The average well depth in Redlands, California is 358 feet, based on 325 wells on record. Well depths range from 24 to 1250 feet depending on geology and location.

How much does it cost to drill a well in Redlands, CA?

Well drilling costs in Redlands typically range from $16,110-$26,850 based on the 358-foot average depth. Call Southern California Well Service at (760) 440-8520 for a free estimate.

Average Well Depth in Redlands, CA

Well Statistics for Redlands

358ft

Average Depth

325

Wells on Record

24-1250ft

Depth Range

380.7

Avg Yield (GPM)

Need a Well Drilled in Redlands?

Expert well drilling, pump installation, and repair service in Riverside County.

📞 (760) 440-8520 Get Free Estimate →

Well Depth Distribution in Redlands

Based on 325 wells drilled in Redlands, California, the average depth is 358 feet. The median depth is 382 feet, which represents the typical well depth in the area.

24ft
Shallowest 358ft
Average 1250ft
Deepest

Shallowest well: 24 feet
Deepest well: 1250 feet
Average depth: 358 feet
Median depth: 382 feet

Geology and Groundwater in Redlands

Wells in Redlands reach moderate depths, averaging 358 feet. The area features a mix of alluvial deposits and bedrock formations, with depth varying based on specific location and proximity to fracture zones. Riverside County geology in this region typically involves decomposed granite overlaying harder rock, with groundwater found in fractures and weathered zones.

The average static water level (depth to water when the pump is off) in Redlands wells is approximately 143 feet below ground surface.

Drilling Trends & Well Use

Wells Drilled by Decade

1900s

1910s

1920s

1930s

1950s

1960s

1970s

1980s

1990s

2000s

113

2010s

2020s

Wells by Use Type

Domestic 116 (37%)

Unknown 73 (23%)

Monitoring 52 (17%)

Irrigation - Agriculture 21 (7%)

Public 21 (7%)

Other 15 (5%)

Vapor Extraction 12 (4%)

Test Well 5 (2%)

Estimated Drilling Cost in Redlands

Based on the average well depth of 358 feet, drilling a new well in Redlands typically costs between $16,110 and $26,850. This includes drilling, casing, pump installation, and basic connections. Actual costs vary based on geology, access, and permit requirements.

🔍 Try our free Well Depth Lookup Tool to check well records near your specific address.

📍 Nearby Cities — Well Depth Data

📚 Related Resources

Get Expert Advice for Your Redlands Property

Southern California Well Service has drilled hundreds of wells across Riverside County. We know the local geology and can give you an accurate depth and cost estimate.

Call (760) 440-8520

Licensed C-57 Contractor. CSLB License #1086994.| San Diego, Riverside & San Bernardino Counties

We service all major pump brands including Franklin Electric, Grundfos, Goulds (Xylem), and Sta-Rite (Pentair). Our trucks carry common parts and components for same-day repairs.

Frequently Asked Questions

How do I know if my well pump needs repair?

Common signs include: no water or low pressure, pump cycling on and off rapidly (short cycling), unusual noises, dirty or sandy water, and higher-than-normal electric bills. Any of these warrant a professional inspection.

How much does well pump repair cost?

Simple repairs like pressure switch replacement run

50-$300. Motor or pump replacement typically costs ,500-$4,500 depending on well depth and pump type. We diagnose the issue before recommending repairs.

Can I repair my well pump myself?

Surface-level issues like pressure switch adjustment or breaker resets are safe DIY tasks. However, anything involving pulling the pump from the well requires specialized equipment and should be handled by a licensed contractor to avoid damaging the well casing.

Continue learning about well maintenance and troubleshooting