How deep are wells in Romoland, CA?

The average well depth in Romoland, California is 331 feet, based on 75 wells on record. Well depths range from 34 to 905 feet depending on geology and location.

How much does it cost to drill a well in Romoland, CA?

Well drilling costs in Romoland typically range from $14,895-$24,825 based on the 331-foot average depth. Call Southern California Well Service at (760) 440-8520 for a free estimate.

Average Well Depth in Romoland, CA

Well Statistics for Romoland

331ft

Average Depth

Wells on Record

34-905ft

Depth Range

83.8

Avg Yield (GPM)

Need a Well Drilled in Romoland?

Expert well drilling, pump installation, and repair service in Riverside County.

📞 (760) 440-8520 Get Free Estimate →

Well Depth Distribution in Romoland

Based on 75 wells drilled in Romoland, California, the average depth is 331 feet. The median depth is 300 feet, which represents the typical well depth in the area.

34ft
Shallowest 331ft
Average 905ft
Deepest

Shallowest well: 34 feet
Deepest well: 905 feet
Average depth: 331 feet
Median depth: 300 feet

Geology and Groundwater in Romoland

Wells in Romoland reach moderate depths, averaging 331 feet. The area features a mix of alluvial deposits and bedrock formations, with depth varying based on specific location and proximity to fracture zones. Riverside County geology in this region typically involves decomposed granite overlaying harder rock, with groundwater found in fractures and weathered zones.

The average static water level (depth to water when the pump is off) in Romoland wells is approximately 74 feet below ground surface.

Drilling Trends & Well Use

Wells Drilled by Decade

1940s

1950s

1970s

1980s

1990s

2000s

2010s

Wells by Use Type

Domestic 44 (59%)

Irrigation - Agriculture 14 (19%)

Unknown 7 (9%)

Monitoring 7 (9%)

Test Well 1 (1%)

Cathodic Protection 1 (1%)

Public 1 (1%)

Estimated Drilling Cost in Romoland

Based on the average well depth of 331 feet, drilling a new well in Romoland typically costs between $14,895 and $24,825. This includes drilling, casing, pump installation, and basic connections. Actual costs vary based on geology, access, and permit requirements.

🔍 Try our free Well Depth Lookup Tool to check well records near your specific address.

📍 Nearby Cities — Well Depth Data

📚 Related Resources

Get Expert Advice for Your Romoland Property

Southern California Well Service has drilled hundreds of wells across Riverside County. We know the local geology and can give you an accurate depth and cost estimate.

Call (760) 440-8520

Licensed C-57 Contractor. CSLB License #1086994.| San Diego, Riverside & San Bernardino Counties

We service all major pump brands including Franklin Electric, Grundfos, Goulds (Xylem), and Sta-Rite (Pentair). Our trucks carry common parts and components for same-day repairs.

Frequently Asked Questions

How do I know if my well pump needs repair?

Common signs include: no water or low pressure, pump cycling on and off rapidly (short cycling), unusual noises, dirty or sandy water, and higher-than-normal electric bills. Any of these warrant a professional inspection.

How much does well pump repair cost?

Simple repairs like pressure switch replacement run

50-$300. Motor or pump replacement typically costs ,500-$4,500 depending on well depth and pump type. We diagnose the issue before recommending repairs.

Can I repair my well pump myself?

Surface-level issues like pressure switch adjustment or breaker resets are safe DIY tasks. However, anything involving pulling the pump from the well requires specialized equipment and should be handled by a licensed contractor to avoid damaging the well casing.

Continue learning about well maintenance and troubleshooting